If you have a slot machine or you have bought one old used vintage slot machine and want to have some fixes to get it work then obviously you will think you need a machine technician. Many of you will even think of taking it to some repair station to get things done. But here in the guide you will find some of the repairs that you yourself can do with your slot machine and you need not need to join machine technical repair training school.

Like any other machines Slot machines too are a blend of electronic and mechanical components, that wear with age and require routine repairs. Before you begin to repair yourself do note that every slot machine that you have purchased whether old or new comes with installation and user guide manual. You need to read that many a times until you are familiar with each components and parts of the slot machine and understand thoroughly as how the slot machine works.

Sales: 1-937-743-2389. Service: 1-937-746-7568. 430 Conover Drive, Franklin, OH 45005. Periodic Slot Machine Maintenance. To maintain the performance of your slot machines, we recommend scheduling periodic maintenance every 3 years. During these maintenance visits, the technician will replace batteries and lights, make tune-ups, and install new components as necessary. Sales: 1-937-743-2389. Service: 1-937-746-7568. 430 Conover Drive, Franklin, OH 45005.

In your guide to repair slot machines you will find some common repairs that can be carried out by you, some videos to watch as well. If your slot machine has some complex issue then obviously you require a qualified technician.

Changing the Top Florescent Light

The top florescent light bulb is easily changed by following these simple procedures. The replacement bulb is an F15T8/CW 18″ 15 Watt bulb which is available at most hardware and department stores or may be purchased online at Ebay or Amazon or realslotmachinesforsale under the category ‘parts of slot machine’.

Open the main slot machine door and ensure the door is fully open. Turn off the power to the slot machine. The power switch can be found with the main door open about midway down on the right side just inside the machine.
If the machine is equipped with a top ticket printer, you must pull the bottom of the printer out far enough to see where the ticket paper is located, and note the area large enough to place a couple of your left fingers under.

Remove the top metal trim strip which is a cover plate to the right of the ticket printer and/or is located along the bottom of the top glass. There are a couple of clips on the back of the metal trim strip that fit into notches on metal bracket which holds the top glass. The metal trim strip should be lifted upwards and outwards to remove.
Once the metal trim strip is removed, the next step is to remove the top glass. Note that some top metal trim strips have a slot in the top that holds the top glass and they must be removed very carefully as to not damage or drop the top glass.

You can now see the top glass is held in place by usually two or three clips that rise above the metal bracket behind the top metal trim strip. Now slowly lift up on the top glass from both bottom edges until the top glass until it is high enough to gently pull it forward and allowing it to slide down and away from the top track and clips holding it in place.
Once the top glass has been removed, put it somewhere where it will not get knocked over or broken. You will see the florescent bulb in the middle of the top box area of the machine. Care should be taken removing the bulb as it may be very hot. Remove the old bulb by twisting the florescent tube about a quarter to half turn allowing the two prongs on the bulb to slide out of the fixture on both sides of the bulb.

Remove and discard the old bulb. To install the new bulb, align the two prongs on each side of the florescent tube with the slits on each fixture in the top box of the slot machine. Twist the bulb into place normally using about a quarter to half of a turn. If the bulb is not secure or aligned, repeat the procedure.
If your slot machine is an IGT S Plus machine, it is equipped with a florescent bulb starter. Then you can replace the starter when replacing the florescent light bulb. The starter is an FS-U Universal Starter. They are available at most hardware and department stores or may be ordered online too. The starter for the top florescent bulb on an IGT S Plus machine is located directly behind the florescent bulb fixture on the left side of the slot machine in the top box area.
It is replaced by twisting about a quarter to half a turn as it is held in place with a bayonet type mount. Remove the old starter and discard. Replace with a new FS-U Universal Starter by aligning the two pins on the bottom of the starter with the notches in the starter receptacle, pushing it up into the starter socket, and then twisting it a quarter to half a turn into place.
Prior to re-installing the top glass, turn the power switch on the right inside of the machine on to verify the bulb works properly. If it does not, turn the power off and check that the bulb is properly installed and secure. If replacing a starter, check that it is also properly installed and secure.
After verifying the bulb is working, it is now time to replace the top glass. If your slot machine has a top ticket printer, ensure the ticket printer is still pulled out so you can place your fingers in the opening while replacing the top glass.
Carefully and slowly lift up the top glass placing each hand under the bottom of the top glass. Slide it into the upper edge track on the top box of the slot machine carefully lifting it so it slides into the tracks while being able to push the top glass back far enough to clear the two or three raised clips on the metal bracket where the top glass holding track is located.
Gently and slowly lower the top glass behind the clips so as to allow them to hold the glass in place. If properly secured, the top glass will not be able to slide down or out of its position. Keep a secure hold on the top glass until you are certain it is secured in the proper position.
Replace the top metal trim strip by aligning the two or three hooks the back through the metal bracket that supports and holds the top glass. Once the hooks on the back are in place, gently push the top metal trim strip down and it should snap into place. If you have a slot machine with a top ticket printer, close it tight into position. Close the main slot machine door and you are ready to play.

Changing the Belly Glass Florescent Light

The belly glass florescent light bulb is easily changed by following these simple procedures. The replacement bulb is an F15T8/CW 18″ 15 Watt bulb which is available at most hardware and department stores or may be bought online as spare parts of slot machine.

Working Slot Machines For Sale

Open the main slot machine door. Turn off the power to the slot machine. The power switch can be found with the main door open about midway down on the right side just inside the machine.
Facing the slot machine door, look on the right side of the door just around from bill acceptor area. You will see a knob sticking out that is approximately the size of the end of a regular pencil. This knob when pulled out releases the slot machine belly glass assembly (belly door) to fold down so the bulb can be accessed.

There are a couple of very important thing to remember prior to pulling this knob to release the belly door. First try pulling gently on the knob. If it does not allow you to pull out and you have a lock installed directly above it, the lock must unlocked in order to allow the release knob to pull out. When pulling out the release knob, be ready for the belly door to fold down.
Most of the time you must lightly pull on both sides of the belly door to get it to fold down, however always place your hand under it so it does not fall down too quickly causing the belly glass to break or crack.
Once the belly door is in the down position, you will see the access to the florescent bulb bracket that is held in place by a small Phillips screw. Remove the screw and place it the coin tray so it will be handy when you need it after replacing the bulb.

The long metal bracket that holds the florescent bulb must be slid slightly right or left so as to be able to lift it out of the belly door. Gently lift the metal bracket with florescent bulb out of the assembly far to be able to turn it over to replace

Real Size Slot Machine